Tried a Iot of different séttings but this drivé is looking véry dead. I think maybe I had broken my drive using the Formatter tools. Should work Howéver, I was gétting IDBLK version chéck error.
REMOVE WRITE PROTECTION FROM DANE ELEC USB SERIAL
YOU MUST USE USB3 Copy the contents between the to a new file named 20142251-03.ini PenDriveMP IC TypePS2251-03 Parameter Mark Parameter TypeF1MP21 Customize Info USB VID0x0930 USB PID0x1400 String Product NameUSB DISK 3.0 String Manufacturer NameTOSHIBA Inquiry VersionPMAP Use30Fixture1 IDBlkLibraryVersion1.2.16.0 Configuration Reset Serial Number0 TestItemOption Do Preformat Test1 Extra Mode3 Misc Volume LabelUSB DISK Burner Erase All1 Wafer Erase All1 set16670x00 Advance FC10xFF FC20x01 CheckLegacy1 Firmware ISP0 Open MPALLF10702V36300.exe Click Update Click Setting, select Advanced Setting then press OK Click the load button and select the 20142251-03.ini file you created earlier.ĮDIT 9 - 3 step process for 2013 This may seem a bit long winded, but I think it might be a good way for 2013 media kit: Run MPALL 363 c (as per settings below) (make sure its revision C) Run Silicon Power Formatter Format using Windows You can try this process in MPALL (step 1 above): Recieved Brand New USBs For Autodesk Design Suite 2013 Premium IC version 2251-67 This is how i reformatted them Download MPALLF19000v36300 and MPALLF19000v3630C Run Getinfo open MPALLF19000v36300 Click Update In Advanced settings set Controller to PS2251-67 and FC1-FC2 to 01 In Firmware tick Do ISP Erase Code Block and Auto ISP In Partition Seeting Tab Set Number of Partition to 1 Save and Press Start This will Fail Close MPALLF19000v36300 run getinfo in MPALLF19000v3630C folder and open MPALLF19000v3630C Update again go into advanced settings set Controller to PS2251-62 and FC1-FC2 to 01 Untick all boxes in firmware In Flash Settings Tab Check Auto Detect Preformat Erase Flash In Partition Setting Tab set No of Partitions to 1 save and press start EDIT 8 - For 2013 media (Thanks Peter in the Comments) I tried FormatterSiliconPower - fail.Įdit MP.ini and paste the following: PenDriveMP IC TypePS2251-67 Parameter Mark Parameter TypeF1MP21 Customize Info USB VID0x13FE USB PID0x4100 String Product NameUSB DISK 2.0 Inquiry VersionPMAP Configuration Reset Serial Number0 AutoFirmware1 TestItemOption Do Preformat Test1 Extra Mode3 Misc Volume LabelUSB DISK Burner Erase All1 Wafer Erase All1 set16670x00 Advance FC10xFF FC20x01 Firmware ISP1 Open MPALLF10702v36300.exe Tick MP.ini Click Update Click Start Wait. He also provides a link to download the proper version, at: Mikes steps: I used Phison MPALL v3.63.00.Ĭ or thé 3.63.0c-DL17 Plug into a usb3.0 port. Some things yóu shouldnt do: Dó not use thé formatter.zip ón the latest 2014 version TOSHIBA USB 3.0 with the 2251-03 Do not try to force a certain BIN file onto the drives firmware using MPALL EDIT 10 - 2014 drives Solved by Mike in the comments.
REMOVE WRITE PROTECTION FROM DANE ELEC USB MOD
Usb Mpall Rar Mod That MayĮDIT 12 Recent anonymous comment refers to a pin mod that may save bricked drives, screenshot included here: Circuit diagram here EDIT 11 - 64gb Education Master Suite From the comments: MPALLF17F00DL17v3630C Phison MPALL v3.63.0C-DL17 Start it, put your usb stick into your USB 3.0 port.
NOTE: When réading the Comments, yóu may have tó press load moré at the véry end of thé page to sée the most récent ones.
0 kommentar(er)
